Home > Manufacturers > Geiselle

Geiselle Products for Sale at Northern Rifleman

Sort By:
Page of 2
02-243 Geissele Barrel Nut Wrench

The Geissele Barren Nut Wrench is designed to be used with Geissele Barrel Nuts.

List Price: $9.00
Our Price: $9.50
169 in stock!
04-246 Geissele SPR 42 Tungsten BFR Weight

To change the Geissele Automatics H1 Buffer assembly to the heavier H2 or H3 buffer setup, you will need to disassemble and re-assemble the buffer replacing the steel weights with the correct number of tungsten weights

1 Tungsten weight to add over all weight to your buffer setup. (H1 / H2 / H3 setups)

List Price: $20.00
Our Price: $21.00
117 in stock!
08-153 Geissele Maritime Bolt Catch

The Geissele Maritime Bolt Catch is designed with the warfighter in mind and will work with any lower receiver designed to accept a mil-spec M16/M4 Carbine bolt catch. The increased surface area promotes ease of function when locking back the bolt or releasing the bolt after a magazine change. In addition, the extended controls add an increased functionality for left handed shooters who no longer have to break their grip to manipulate the bolt catch. Left handed shooters can easily reach the controls using the index finger of their left hand making magazine changes and locking the bolt back much more fast and efficient. Aggressive checkering covers the surface of the levers giving the Geissele Maritime Bolt Catch a textured surface that enables positive feedback to the shooters hand when being used with gloves or at night. Manufactured from properly heat treated 8620 steel and manganese phosphate coated, the Geissele Maritime Bolt Catch is intended to serve as an enhanced mil-spec replacement and assist in giving our warfighters overmatch capability with the M16/M4 carbine platform.

Please Note: A mil-spec bolt catch spring and plunger are required for assembly and are NOT included. If the Maritime Bolt Catch is replacing an existing mil-spec bolt catch, please use care when disassembling the component from your lower receiver as you will need these parts to install the Maritime Bolt Catch. Compatibility with billet AR-15 lower receivers is unknown. Please also note that the extended controls of the Geissele Maritime Bolt Catch will partially cover the pin hole for the hammer, a smaller punch may be required to push the hammer pin out of the receiver from the left side, and the hammer pin should only be installed from the right side of the receiver.

List Price: $29.00
Our Price: $30.25
581 in stock!
05-495 Geissele Super 42 Braided Wire Buffer & Spring Combo

The Geissele Super 42 Spring was designed to improve the function and reliability of your AR-15 pattern rifle. Its unique spring design uses three independent strands of wire, just like the German MG42 Machine Gun. This concept acts as a harmonic damper and energy absorber by allowing the springs to flex separately from each other. This flex helps displace excess energy which decreases the chance of spring failure and assists with making your AR-15 more reliable.

Compared to the stock spring, The Geissele Super 42 Spring has a decreased tendency to lose length and force over a given round count. As an added bonus, it removes the annoying spring reverberations (twang) heard and felt by the shooter through the buttstock. The Super 42 Spring has a 15% stronger average return force than the standard buffer spring. This will assist in stripping rounds out of the magazine when operating with a dirty weapon or when using steel-case ammo.

List Price: $65.00
Our Price: $68.00
767 in stock!
05-807N Geissele Super Gas Black Nitride

Super Gas Block with Nitride coating - The bore of the SGB is machined to closely fit around .750” diameter mounting bosses found on most M4 Carbines and AR-15 rifles.

List Price: $80.00
Our Price: $83.50
414 in stock!
05-495-H2 Geissele Super 42 Braided Wire H2 Buffer & Spring

The Geissele Super 42 Spring was designed to improve the function and reliability of your AR-15 pattern rifle. Its unique spring design uses three independent strands of wire, just like the German MG42 Machine Gun. This concept acts as a harmonic damper and energy absorber by allowing the springs to flex separately from each other. This flex helps displace excess energy which decreases the chance of spring failure and assists with making your AR-15 more reliable.

Compared to the stock spring, The Geissele Super 42 Spring has a decreased tendency to lose length and force over a given round count. As an added bonus, it removes the annoying spring reverberations (twang) heard and felt by the shooter through the buttstock. The Super 42 Spring has a 15% stronger average return force than the standard buffer spring. This will assist in stripping rounds out of the magazine when operating with a dirty weapon or when using steel-case ammo.

List Price: $82.00
Our Price: $85.75
147 in stock!
05-497B Geissele Airborne Charge Handle 5.56 Black

The Airborne Charging Handle (ACH) was developed at the request of an elite organization famous for its expertise in aerial insertion. The organization requested a lower profile lever design to reduce the chances of snagging. The ACH’s lower profile design is especially ideal for rifles where the primary sighting system is a red dot or similar low profile optic system. The ambidextrous ACH is 3D machined from a solid block of aircraft grade 7075-T6 aluminum. Shortened levers are dual contoured with gently concaved radius cuts in the vertical and horizontal planes. The handling surfaces of the levers are checkered for confident operation while wearing gloves. A taller fence at the rear of the ACH aids in redirecting gas blow back when shooting with short barreled and suppressed weapon systems. The ACH and its components are Type 3 Hardcoat anodized and are available in Black and DDC (Desert Dirt Color).

List Price: $94.00
Our Price: $98.25
(Out of Stock)
05-664B Geissele USASOC Charge Handle Black

High quality components and precise manufacturing make Geissele parts ideal for maintaining and upgrading firearms. The durability, reliability and excellent build quality of these parts will ensure years of service you can count on.

List Price: $100.00
Our Price: $102.00
(Out of Stock)
10-169 Geissele AR15/M4 Reaction Rod

The Geissele Reaction Rod (5.56/.223) makes the removal and installation of barrels, flash hiders, gas blocks and hand guards much easier and simpler.

The Reaction Rod is designed to be gripped in a bench vise so that the rod is either horizontal or vertical. The upper receiver is then slid onto the rod and the rod’s integral splines enter the barrel extension and secure the barrel extension from turning. This allows all the torque from barrel nut wrenches to go directly into the barrel extension. In contrast, receiver vise blocks transmit the turning force into the aluminum receiver, a good part of which passes through the small, easily distorted receiver index pin. With the Geissele Reaction Rod, marring of an upper receiver’s finish by gripping and twisting inside vise blocks is eliminated and so is the need to remove sights and mounts from the receiver’s M1913 rail.

The Geissele Reaction Rod (5.56/.223) is machined at Geissele Automatics’ state of the art manufacturing facility in North Wales, Pennsylvania. The rod is cut from a solid bar of 4140 Chrome Moly steel, properly quenched/tempered and ground to an exact diameter that is smooth and straight so the rod will enter an upper receiver without wobble.

List Price: $99.00
Our Price: $103.50
16 in stock!
05-495-H3 Geissele Super 42 Braided Wire H3 Buffer & Spring

The Geissele Super 42 Spring was designed to improve the function and reliability of your AR-15 pattern rifle. Its unique spring design uses three independent strands of wire, just like the German MG42 Machine Gun. This concept acts as a harmonic damper and energy absorber by allowing the springs to flex separately from each other. This flex helps displace excess energy which decreases the chance of spring failure and assists with making your AR-15 more reliable.

Compared to the stock spring, The Geissele Super 42 Spring has a decreased tendency to lose length and force over a given round count. As an added bonus, it removes the annoying spring reverberations (twang) heard and felt by the shooter through the buttstock. The Super 42 Spring has a 15% stronger average return force than the standard buffer spring. This will assist in stripping rounds out of the magazine when operating with a dirty weapon or when using steel-case ammo.

List Price: $99.00
Our Price: $103.50
400 in stock!
05-313B Geissele Super Charging Handle AR15 SCH Black

The Super Charging Handle (SCH®) is 3D machined from a solid block of aircraft grade 7075-T6 aluminum. Its ambidextrous design allows for seamless operation from either side of the weapon. The levers are dual contoured similar to that of the charging handle of an M14, where not only the x-axis but also the y-axis receive radius cuts. The handling surface of the lever is also checkered, adding a textured grip aiding to the use when operating with gloves. The heightened rear lip of the SCH aids in mitigating gas blow back to the shooter when shooting with short barreled and suppressed weapon systems. All parts are then Type 3 Hardcoat anodized and are available in black and DDC (Desert Dirt Color).

MSRP $105.00
Our Price: $109.75
(Out of Stock)
05-664S Geissele USASOC Charge Handle Desert Dirt Color

High quality components and precise manufacturing make Geissele parts ideal for maintaining and upgrading firearms. The durability, reliability and excellent build quality of these parts will ensure years of service you can count on.

List Price: $110.00
Our Price: $112.00
(Out of Stock)
05-313S Geissele Super Charging Handle AR15 SCH Desert Dirt Color

The Super Charging Handle (SCH®) is 3D machined from a solid block of aircraft grade 7075-T6 aluminum. Its ambidextrous design allows for seamless operation from either side of the weapon. The levers are dual contoured similar to that of the charging handle of an M14, where not only the x-axis but also the y-axis receive radius cuts. The handling surface of the lever is also checkered, adding a textured grip aiding to the use when operating with gloves. The heightened rear lip of the SCH aids in mitigating gas blow back to the shooter when shooting with short barreled and suppressed weapon systems. All parts are then Type 3 Hardcoat anodized and are available in black and DDC (Desert Dirt Color).

MSRP $115.00
Our Price: $120.25
31 in stock!
05-497S Geissele Airborne Charge Handle 5.56 Desert Dirt Color

The Airborne Charging Handle (ACH) was developed at the request of an elite organization famous for its expertise in aerial insertion. The organization requested a lower profile lever design to reduce the chances of snagging. The ACH’s lower profile design is especially ideal for rifles where the primary sighting system is a red dot or similar low profile optic system. The ambidextrous ACH is 3D machined from a solid block of aircraft grade 7075-T6 aluminum. Shortened levers are dual contoured with gently concaved radius cuts in the vertical and horizontal planes. The handling surfaces of the levers are checkered for confident operation while wearing gloves. A taller fence at the rear of the ACH aids in redirecting gas blow back when shooting with short barreled and suppressed weapon systems. The ACH and its components are Type 3 Hardcoat anodized and are available in Black and DDC (Desert Dirt Color).

List Price: $115.00
Our Price: $120.25
(Out of Stock)
05-476B Geissele Super Charging Handle AR10 7.62 Black

The Super Charging Handle (SCH®) is 3D machined from a solid block of aircraft grade 7075-T6 aluminum. Its ambidextrous design allows for seamless operation from either side of the weapon. The levers are dual contoured similar to that of the charging handle of an M14, where not only the x-axis but also the y-axis receive radius cuts. The handling surface of the lever is also checkered, adding a textured grip aiding to the use when operating with gloves. The heightened rear lip of the SCH aids in mitigating gas blow back to the shooter when shooting with short barreled and suppressed weapon systems.

All parts are then Type 3 Hardcoat anodized and are available in Black and DDC (Desert Dirt Color).

List Price: $140.00
Our Price: $146.25
2 in stock!
05-476S Geissele Super Charging Handle AR10 7.62 DDC

The Super Charging Handle (SCH®) is 3D machined from a solid block of aircraft grade 7075-T6 aluminum. Its ambidextrous design allows for seamless operation from either side of the weapon. The levers are dual contoured similar to that of the charging handle of an M14, where not only the x-axis but also the y-axis receive radius cuts. The handling surface of the lever is also checkered, adding a textured grip aiding to the use when operating with gloves. The heightened rear lip of the SCH aids in mitigating gas blow back to the shooter when shooting with short barreled and suppressed weapon systems.

All parts are then Type 3 Hardcoat anodized and are available in Black and DDC (Desert Dirt Color).

List Price: $150.00
Our Price: $156.75
3 in stock!
05-145 Geissele 2 Stage G2S Trigger

The Geissele 2 Stage (G2S) was designed to be a high quality, cost effective option of the Super Semi-Automatic (SSA®) trigger.

The G2S is a non-adjustable trigger that is a precision two-stage trigger and allows precise and accurate trigger control. The G2S is manufactured from the same tool steel as the SSA and the sears are also wire EDM cut. Visually, from the outside of the weapon there is no difference from the SSA and the feel and reliability is the same. The G2S however has a different way of holding the hammer pin in place, there is no laser markings, and the parts are only spot checked for MP.

PLATFORM: AR15/AR10
TYPE: 2 Stage
1st STAGE WEIGHT RANGE: 2.75 - 3 lbs.
2nd STAGE WEIGHT RANGE: 1.5 - 1.75 lbs.
TOTAL PULL WEIGHT RANGE: 4.25 - 4.75 lbs.
ADJUSTABLE: No
TRIGGER BOW TYPE: M4 Curved
RECOMMENDED USE: Military, Law Enforcement, Home Defense
PIN SIZE: Mil-Spec

MSRP $165.00
Our Price: $172.50
986 in stock!
10-247 Geissele AR10 7.62 Reaction Rod

The Reaction Rod (7.62/.308) makes the removal and installation of barrels, flash hiders, gas blocks and hand guards much easier and simpler. The Reaction Rod is designed to be gripped in a bench vise so that the rod is either horizontal or vertical. The upper receiver is then slid onto the rod and the rod’s integral splines enter the barrel extension and secure the barrel extension from turning. This allows all the torque from barrel nut wrenches to go directly into the barrel extension. In contrast, receiver vise blocks transmit the turning force into the aluminum receiver, a good part of which passes through the small, easily distorted receiver index pin. With the Geissele Reaction Rod, marring of an upper receiver’s finish by gripping and twisting inside vise blocks is eliminated and so is the need to remove sights and mounts from the receiver’s M1913 rail.

List Price: $199.00
Our Price: $208.00
(Out of Stock)
05-1213 Geissele Barrel Assembly 16" 5.56

Geissele Automatics Barrel Assembly

.223 Wylde
16" Barrel
Black Finish
Gas Block and Tube Included
Button-Rifled

List Price: $230.00
Our Price: $240.50
(Out of Stock)
05-101 Geissele Super Semi-Automatic SSA

The Geissele Super Semi-Automatic (SSA®) trigger is a semi-automatic only version of Geissele Automatics’s Super Select-Fire trigger. The SSA is a non-adjustable combat trigger that is a precision two-stage trigger and allows precise and accurate trigger control. The SSA’s two-stage design allows the trigger to be light enough for accurate and precise shots, but forgiving enough for CQB. The SSA is safety certified by Crane Naval Surface Warfare Center. It is recommended for demanding applications such as Law Enforcement use, Close Quarters Battle (CQB) and mid-range carbine work.

PLATFORM: AR15/AR10
TYPE: 2 Stage
1st STAGE WEIGHT RANGE: 2.75 - 3 lbs.
2nd STAGE WEIGHT RANGE: 1.5 - 1.75 lbs.
TOTAL PULL WEIGHT RANGE: 4.25 - 4.75 lbs.
ADJUSTABLE: No
TRIGGER BOW TYPE: M4 Curved
RECOMMENDED USE: Law Enforcement, Home Defense, Hunting
PIN SIZE: Mil-Spec

List Price: $240.00
Our Price: $251.00
1349 in stock!
05-152 Geissele Super 3 Gun Mil-Spec Pin S3G Trigger

The Geissele Super 3 Gun (S3G) is a semi-automatic, hybrid cross between a single-stage trigger and a traditional 2-stage trigger. Its robust feel and light pull weight, combined with a lightning-quick reset, make this trigger ideal for any 3 Gun competitor.

The S3G trigger has a very short, light pull and reset. We do not recommend it for duty use, bench rest, accuracy work or shooting small groups. It is designed for close course competition use where rapid target engagement with quick follow up shots are required.

PLATFORM: AR15/AR10
TYPE: Hybrid Rolling Break
TOTAL PULL WEIGHT: 3.0 - 4.0 lbs. (Lighter Spring) 4.5 - 5.5 lbs. (Heavier Spring)
ADJUSTABLE: No
TRIGGER BOW TYPE: M4 Curved
RECOMMENDED USE: 3 Gun Competition
PIN SIZE: Mil-Spec

List Price: $240.00
Our Price: $251.00
442 in stock!
05-160 Geissele SPR Semi-Automatic Enhanced SSA-E Trigger

Built on the chassis of the Geissele SSA, the Super Semi-Automatic Enhanced (SSA-E) provides enhanced trigger control and weapon accuracy while maintaining the robustness and reliability of our combat-proven two-stage trigger. The SSA-E’s reduced first and second stage pull weights result in a trigger with a smooth, light first stage take-up and a crisp, candy cane-like second stage break. The SSA-E is ideal for use in precision Squad Designated Marksman type rifles where weapon accuracy and reliability are critical and a non-adjustable drop in trigger is desired.

The Geissele Super Semi-Automatic Enhanced (SSA-E) Trigger is a finely-tuned semi-automatic-only version of our full-auto, two stage combat trigger presently used in the U.S. Special Operations Community.

PLATFORM: AR15/AR10
TYPE: 2 Stage
1st STAGE WEIGHT RANGE: 2.0 - 2.5 lbs.
2nd STAGE WEIGHT RANGE: 0.9 - 1.3 lbs.
TOTAL PULL WEIGHT RANGE: 2.9 - 3.8 lbs.
ADJUSTABLE: No
TRIGGER BOW TYPE: M4 Curved
RECOMMENDED USE: Target & Precision Shooting, Hunting
PIN SIZE: Mil-Spec

List Price: $240.00
Our Price: $251.00
1241 in stock!
05-165 Geissele Super Dynamic Combat SD-C Trigger

The Geissele Super Dynamic-Combat (SD-C) Trigger featuring an exclusive flat trigger bow, is a rugged, non-adjustable combat trigger with a sear design that provides a wide margin of safety against unintentional discharges yet still gives the operator a sharp, repeatable trigger release.

The SD-C is a flat bow variant of the Super Semi-Automatic (SSA®) trigger.

PLATFORM: AR15/AR10
TYPE: 2 Stage
1st STAGE WEIGHT RANGE: 2.75 - 3.0 lbs.
2nd STAGE WEIGHT RANGE: 1.5 - 1.75 lbs.
TOTAL PULL WEIGHT RANGE: 4.25 - 4.75 lbs.
ADJUSTABLE: No
TRIGGER BOW TYPE: Flat
RECOMMENDED USE: Law Enforcement, Home Defense, Hunting
PIN SIZE: Mil-Spec

List Price: $240.00
Our Price: $251.00
701 in stock!
05-166 Geissele Super Dynamic 3 Gun SD-3G Trigger

The Geissele Super Dynamic 3 Gun (SD-3G) trigger is the flat trigger bow version of the Geissele Super 3 Gun (S3G) trigger. Like the S3G, the SD-3G has a shortened pull length and a lightning-quick reset to give it a unique, hybrid trigger pull that is a cross between a traditional two-stage and single-stage trigger while still retaining the safety and robustness of a two-stage combat trigger. The SD-3G’s flat trigger bow further enhances the trigger’s performance by reducing the perceived pull weight and improving the trigger’s tactile feedback to the operator making it ideally suited for 3 Gun competition shooting.

The SD3G trigger has a very short, light pull and reset. We do not recommend it for duty use, bench rest, accuracy work or shooting small groups. It is designed for close course competition use where rapid target engagement with quick follow up shots are required.

PLATFORM: AR15/AR10
TYPE: Hybrid Rolling Break
TOTAL PULL WEIGHT: 3.0 - 4.0 lbs. (Lighter Spring) 4.5 - 5.5 lbs. (Heavier Spring)
ADJUSTABLE: No
TRIGGER BOW TYPE: Flat
RECOMMENDED USE: 3 Gun Competition
PIN SIZE: Mil-Spec

List Price: $240.00
Our Price: $251.00
1178 in stock!
05-167 Geissele Super Dynamic Enhanced SD-E Trigger

The Geissele Super Dynamic-Enhanced (SD-E) Trigger featuring an exclusive flat trigger bow, is a finely-tuned two stage trigger providing enhanced trigger control and weapon accuracy while maintaining the robustness and reliability of our combat-proven two-stage trigger.

PLATFORM: AR15/AR10
TYPE: 2 Stage
1st STAGE WEIGHT RANGE: 2.0 - 2.5 lbs.
2nd STAGE WEIGHT RANGE: 0.9 - 1.3 lbs.
TOTAL PULL WEIGHT RANGE: 2.9 - 3.8 lbs.
ADJUSTABLE: No
TRIGGER BOW TYPE: Flat
RECOMMENDED USE: Target & Precision Shooting, Hunting
PIN SIZE: Mil-Spec

List Price: $240.00
Our Price: $251.00
1304 in stock!
05-230 Geissele Super Tricon Trigger

Designed in cooperation with Jeff Gonzales former Navy SEAL of Trident Concepts, the Super Tricon Trigger comes standard with a two-stage design for safety and control; a carrot-like 2nd stage break; full-power hammer spring; tool steel construction; and unique trigger bow design with ribbed surface.

PLATFORM: AR15/AR10
TYPE: 2 Stage
1st STAGE WEIGHT RANGE: 2.75 - 3 lbs.
2nd STAGE WEIGHT RANGE: 1.5 - 1.75 lbs.
TOTAL PULL WEIGHT RANGE: 4.25 - 4.75 lbs.
ADJUSTABLE: No
TRIGGER BOW TYPE: Tricon
RECOMMENDED USE: Law Enforcement, Home Defense, Hunting
PIN SIZE: Mil-Spec

List Price: $240.00
Our Price: $251.00
140 in stock!
05-1214 Geissele Barrel Assembly 11.5" 5.56

Geissele Automatics Barrel Assembly

.223 Wylde
11.5" Barrel
Black Finish.
Gas Block and Tube Included
Button-Rifled

List Price: $230.00
Our Price: $253.50
(Out of Stock)
05-283B Geissele 9.5" Super Modular Rail MLOK Black

The Super Modular Rail (SMR) MK4 M-LOK™ is Geissele’s ultra-lightweight M-LOK option. These rails are purpose-built and feature integrated M1913 picatinny rail sections at the fore of the rail in the 3, 6 and 9 o’clock positions. Maximum venting for heat dissipation also dramatically reduces the rail's overall weight, while maintaining its same strong and rigid platform. Utilizing Magpul's M-LOK technology at the 3, 6, and 9 o'clock positions, as well as the upper 45 quadrants.

The SMR MK4 is both versatile and modular, allowing the user to tailor their platform to his or her unique needs. The SMR MK4 also features Geissele's proprietary 2.25" long barrel nut. This increases the surface contact where the rail interfaces with the receiver and creates a platform that can be trusted to be straight and true the entire length of the free float rail. This increases accuracy and zero repeatability during disassembly and reassembly when performing maintenance

MSRP $275.00
Our Price: $287.50
121 in stock!
05-284B Geissele 9.5" MK8 Super Modular MLOK

The Super Modular Rail (SMR) MK8 M-LOK™ is Geissele’s ultra-modular model. The SMR MK8 is one of the first rails available to utilize the Magpul M-LOK technology. These rails are designed to give the user full modularity while maintaining a strong and rigid platform. Maximum venting at the lower 45° quadrants create maximum heat dissipation and also dramatically reduces the rail's overall weight. Utilizing Magpul's M-LOK technology at the 3, 6, and 9 o'clock positions, as well as the upper 45° quadrants.

The SMR MK8 is both versatile and modular, allowing the user to tailor their platform to his or her unique needs. The SMR MK8 also features Geissele's proprietary 2.25" long barrel nut. This increases the surface contact where the rail interfaces with the receiver and creates a platform that can be trusted to be straight and true the entire length of the free float rail. This increases accuracy and zero repeatability during disassembly and reassembly when performing maintenance.

MSRP $275.00
Our Price: $287.50
43 in stock!
05-573B Geissele 13.5" Super Modular MK14 MLOK Black

The MK14 is the latest entry to the Geissele line up of Super Modular Rails. The new handguard design offers a smaller diameter and overall height to create a slimmer package. Included with the MK14 Super Modular Rail is an updated version of the proven Geissele Barrel Nut design, not only providing ease of installation but superior rigidity. The long surface contact of the 2.25” barrel nut interfaces with the receiver creating a platform that can be trusted to be straight and true the entire length of the free float rail. The MK14 is 3d precision machined using 6061-T6 Aluminum due to its strong, rigid and lightweight properties.

Utilizing Magpul’s M-LOK technology in the 3, 6, and 9 o’clock positions allow the end user full customization and modularity of their rifle to securely mount lights, bipods and other firearm accessories. The Geissele MK14 Super Modular rail is finished in a durable and long lasting Type 3 Hardcoat Anodized available in either Black or Geissele’s DDC finish.

NOTE: IF THIS IS YOUR FIRST TIME PURCHASING A GEISSELE AUTOMATICS RAIL, YOU WILL NEED TO PURCHASE A BARREL NUT WRENCH IN ORDER TO PROPERLY INSTALL THE RAIL. CLICK HERE TO PURCHASE

HEIGHT: 2.02"
COLOR: Black
MATERIAL: 6061-T6
FINISH: Type 3 Hardcoat Anodize
AVAILABLE LENGTHS: 9.3", 13.5", 15"
INNER DIAMETER: 1.27"
OUTER DIAMETER (DAQ*): 1.52"
SMR MK14 9.3" WEIGHT: 8oz (9.6oz w/ barrel nut)
SMR MK14 13.5" WEIGHT: 10oz (11.5oz w/ barrel nut)
SMR MK14 15" WEIGHT: 11.6oz (13oz w/ barrel nut)
Weapon Platform AR15/M4/M16

These rails are designed to work with Mil-Spec M4 upper receivers. The compatibility with billet receiver sets is unknown.

List Price: $275.00
Our Price: $287.50
219 in stock!