Magpul Minus 5 Round Limiter – PMAG® AR/M4 GEN M3, 3 Pack

The PMAG Minus 5 Round Limiter installs in 10, 20, or 30 round GEN M3 PMAG bodies, reducing the magazine capacity by five rounds. Designed for sporting and hunting applications, installation of the Limiter is simple, tool-less, and requires no permanent modification of the magazine body.

NOTE: Will NOT make a banned magazine legal! This product is intended for TEMPORARY capacity reduction of PMAG AR/M4 GEN M3 magazines. This product does not constitute a permanent capacity reduction. The user is responsible for knowing applicable laws in any jurisdiction that restricts magazines based on capacity or regulates magazine capacity for hunting. Please check all laws and regulations of your state and locality to determine the legality of your host ammunition magazines.

Made in U.S.A.

Standard AR15 Carbine Hand Guard

2 piece standard carbine hand guard. Carbine length.

Ambidextrous single point sling plate

Lower Vise Block is made of Solvent resistant polymer construction for strength & durability. It allows for safe mounting and will help to prevent any type of distort or damage to the Lower receiver. Great to use when performing your regular maintenance, repairs or weapon assembly. Fits into the magazine housing from either the top or bottom, and the magazine catch will securely lock your receiver into place in the vise.

Low profile gas block is constructed of anodized aircraft grade aluminum with a Matte Finish. The Low profile gas block replaces the existing A2 front sight. It  comes equipped with picatinny rails on top and bottom allowing you to mount accessories such as a front sight or a laser underneath. The top rail is lower than the flat top by 0.28". It is compatibe with 5.56/.223 with a .750 diameter barrel. Roll pin & set screws are included. No modification to your barrel is required.

Original factory Short length Quick Detach Sling Swivel Push-button part to replace damaged or lost piece for your TacFire Inc. receiver end plates with quick detach attachments.

Tacfire Dust Cover

The dust cover seals the ejection port (which allows spent brass to exit the upper receiver after firing) from allowing contaminants such as sand, dirt, or other debris from entering the mechanism.

Tacfire Forward Assist

Forward assist button for AR-15/M4 style rifles.

This product is used to assist putting the bolt into battery.

Key features are:
- Includes roll pin and spring
- Hardened steel construction
- Black Oxide finish

Medium height riser mount is constructed of Lightweight T6 6061 Aircraft grade aluminum for strength & durability. It features a see-through design which allows for use with iron sights. The 0.82 inch riser is designed to lift your mounting surface to allow sight clearance over your front sights. It accepts all Picatinny/Weaver Optics, Red Dots, and other tactical accessories.

Tactical A2 Flash Hider (1/2x28)

The A2 Bird cage Flash Suppressor is the standard muzzle device of the US Armed Forces and found on most M4/M16 rifles as well as most AR-15 rifles. Our A2 Flash Suppressor is finished with a Mil-Spec Heavy Phosphate finish.

Tactical A2 Flash Hider (5/8-24)

The A2 Bird cage Flash Suppressor is the standard muzzle device of the US Armed Forces and found on most M4/M16 rifles as well as most AR-15 rifles. This A2 Flash Suppressor is finished with a Mil-Spec Heavy Phosphate finish.

Tacfire 1.1" Compact Riser Mount

Official TacFire Compact Extra High profile 2 1/2" length riser mount is constructed of Lightweight T6 6061 Aircraft grade aluminum for strength & durability. It features a see-through design which allows for use with iron sights and a Quick Detach Lever. The 1.1" inch riser is designed to lift your mounting surface to allow sight clearance over your front sights. It accepts all Picatinny/Weaver Optics, Red Dots, and other tactical accessories.

Tacfire 13/16" Compact Riser Mount

Official TacFire Compact Medium profile 2 1/2" length riser mount is constructed of Lightweight T6 6061 Aircraft grade aluminum for strength & durability. It features a see-through design which allows for use with iron sights. The 13/16" inch riser is designed to lift your mounting surface to allow sight clearance over your front sights. It accepts all Picatinny/Weaver Optics, Red Dots, and other tactical accessories.

Aluminum Gas Block

Clamp on style gas block. Sized to fit .750” barrels.

.223/.556 1/2"x28 THREAD MUZZLED BRAKE STEEL

AR-15 Charge Handle

Charge Handle manufactured from 6061 Billet Aluminum

Gas Tube - Carbine Length

Carbine Length Gas Tube for AR-15.

Gas Tube - Mid Length

Carbine Length Gas Tube for AR-15.

Gas Tube - Pistol Length

Pistol Length Gas Tube for AR-15.

Gas Tube - Rifle Length

Carbine Length Gas Tube for AR-15.

Bianchi Model 7934 Open Top Handcuff Case

Note: This handcuff case was used by an officer for approximately 8 months. It is still in great condition and priced to sell.

The Model 7934 AccuMold® Elite™ Open Handcuff Case features a pull through style for easy access to the cuffs. Made of trilaminate construction with a synthetic leather-like finish. A dual web belt loop design conveniently accommodates both 2 in. (50 mm) and 2.25 in. (58 mm) belts widths.

Model 7922 Triple Threat™ II Double Magazine Pouch

Note: This Magazine Pouch was used by an officer for approximately 4 months. It is still in great condition and priced to sell.

The Model 7922 AccuMold® Elite™ Triple Threat™ II Double Magazine Pouch is an open top design and features an injection molded belt loop for vertical or horizontal carry. Made with trilaminate construction with a leather-like finish. Slides on a 2.25 in. (58 mm) duty belt.

The PMAG 30 AR/M4 GEN M2 MOE is a 30-round 5.56x45 NATO (.223 Remington) AR15/M4 compatible magazine that offers a cost competitive upgrade from the aluminum USGI.

It features an impact resistant polymer construction, easy to disassemble design with a flared floorplate for positive magazine extraction, resilient stainless steel spring for corrosion resistance, and an anti-tilt, self-lubricating follower for increased reliability.

Made in U.S.A.

Tacfire 13/16" Compact Mount w/ Quick Release

Official TacFire Compact Medium profile 2 1/2" length riser mount is constructed of Lightweight T6 6061 Aircraft grade aluminum for strength & durability. It features a a Quick Detach Lever and a see-through design which allows for use with iron sights. The 13/16" inch riser is designed to lift your mounting surface to allow sight clearance over your front sights. It accepts all Picatinny/Weaver Optics, Red Dots, and other tactical accessories.

PHANTOM STYLE MUZZLE BRAKE

- STEEL
- 223 or .556
- 1/2"x28 threading

Hand Molded Adjustable Cant IWB KYDEX Holster for the Glock G17, G19, G22, G23, G26, G27, G31, G32 and G33 (Gen1-Gen5). These minimalist inside the waistband KYDEX Glock holsters protect your weapon from moisture while remaining extremely lightweight and durable. They are the perfect all around holster for every day concealed carry of your Glock G17, G19, G22, G23, G26, G27, G31, G32 or G33. These holsters are comfortable enough for everyday use and very easy to hide no matter how you are dressed.

Not designed to be carried outside of the waistband.

Hand Molded Adjustable Cant IWB KYDEX Holster for the Glock G36 (Non-Rail). These minimalist inside the waistband KYDEX Glock holsters protect your weapon from moisture while remaining extremely lightweight and durable. They are the perfect all around holster for every day concealed carry of your Glock 36 (Non-Rail. These holsters are comfortable enough for everyday use and very easy to hide no matter how you are dressed.

Not designed to be carried outside of the waistband.